Processing advice

    


Covings

The underground has to be clean, dry, solid, smooth and able to take a weight. Cut corner profiles using a mitre box and a fine saw. Apply solvent-free DECOSA® universal glue thinly on the profile backside. Press profile carefully against ceiling and wall. Remove potential glue rests with a wet sponge immediately. Close open joints with glue or filler. For painting use solvent-free dispersion colour.

To top


Wall profiles

The underground has to be clean, dry, solid, smooth and able to take a weight. Cut corner profiles using a mitre box and a fine saw. Apply solvent-free DECOSA® universal glue thinly on the profile backside. Press profile carefully against ceiling and wall. Remove potential glue rests with a wet sponge immediately. Close open joints with glue or filler. For painting use any dispersion colour.

To top


Rosettes

The underground has to be clean, dry, solid, smooth and able to take a weight. Define position of rosette on ceiling, mark it with a pencil, eventually set a central borehole for light connection. Clean rosette backside and apply DECOSA® universal glue thinly. Excactly position rosette and press firmly against ceiling. Remove potential glue rests with a wet sponge immediately. For painting use solvent-free dispersion colour.

To top


Ceiling tiles

The underground has to be clean, dry, solid, smooth and able to take a weight. Before applying the tiles find out the centre of the ceiling by stretching two diagonal lines. Fix the first tile exactly at the centre of the ceiling and add the other tiles edge to edge. For tiles with directional arrow always keep the same direction. For cutting the tile a sharp knife is sufficient. Apply DECOSA® polystyrene glue with a notched trowel on the backside. Press tiles against ceiling, remove potential glue rests with a wet sponge immediately. For painting use solvent-free dispersion colour.

To top


Ceiling panels

The underground has to be clean, dry, solid, smooth and able to take a weight. Laying can be done without complex substructure depending on the desired pattern. For cutting the panel a sharp knife is sufficient. Apply DECOSA® polystyrene glue with a notched trowel on the backside. Press panel against ceiling, remove potential glue rests with a wet sponge immediately. For the clean and harmonious conclusion between ceiling and wall use matching DECOSA® framings.

To top


Creative stones

The underground has to be clean, dry, solid, smooth and able to take a weight. Apply DECOSA® universal glue on the backside of the decorative stone. Press it to the wall at edges, as well as in composite. Allow approx. 48 hours for drying. The decorative stone can be personalized with solvent-free dispersion paint.

To top


3D-wall tattoos

The underground has to be clean, dry, solid, smooth and able to take a weight. Apply tesa Powerstrip® on the backside and press wall tattoo against the wall. Decoration element can be removed by a circular motion. 3D-wall tattoo can be personalised with solvent free dispersion paint, acrylic paint or other creative techniques, for example decoupage.

To top


Wall vases

The underground has to be clean, dry, solid, smooth and able to take a weight. Apply tesa Powerstrip® on the backside and press wall vase against the wall. Decoration element can be removed by a circular motion. 3D-wall tattoo can be personalised with solvent free dispersion paint, acrylic paint or other creative techniques, for example decoupage. Fill water into the tube, place it in the vase and put a flower in.

To top


Wall frames

The underground has to be clean, dry, solid, smooth and able to take a weight. Apply DECOSA® universal glue on the backside. Set position of the frame and press it firmly to the wall. Remove excess glue immediately with a damp sponge. Optionally, the frame can be additionally anchored by two screws to the wall. To do this, leave the screws in the specified distance (see the holes on the back) about 2.5 cm out of the wall and then put the glued frame on. Allow 48 hours drying before first load. The decoration element can be painted and individually designed with solvent-free dispersion paint or various techniques. It is recommended to do this before installation. More design options result from individual cuts with a standard fine saw or knife.

To top


Wall panels

The underground has to be clean, dry, solid, smooth and able to take a weight. Apply DECOSA® universal glue on the backside. Set position of the panel and press it firmly to the wall. Remove excess glue immediately with a damp sponge. Optionally, the panel can be additionally anchored by two screws to the wall. To do this, leave the screws in the specified distance (see the holes on the back) about 2.5 cm out of the wall and then put the glued panel on. Allow 48 hours drying before first load. The decoration element can be painted and individually designed with solvent-free dispersion paint or various techniques. It is recommended to do this before installation. More design options result from individual cuts with a standard fine saw or knife.

To top


Light bar for LED-Systems

The underground has to be clean, dry, solid, smooth and able to take a weight. Before applying the mouldings cut them to mitre for the corners with the help of a cutting case and a fine saw. Where later the cable is conducted, some space can be cut out with a sharp knife. Apply a thin coat of DECOSA® universal glue on the backside of the moulding. Press the moulding slightly against wall or ceiling. Remove excess glue immediately with a damp sponge. Fill joints with glue or spackle. Use solvent-free dispersion colour to paint the mouldings. After drying, install LED-Stripe according to manufacturer´s instructions.

To top


Clip-on Coving

The underground must be clean, dry, firm, smooth and stable. Before processing cut covings to size with a fine saw. Attach clips with screws on the wall. Position cables and clip the coving on the installed
clips. For painting use any paint or other creative techniques. Just take the covings off the installed clips for adding or removing cables.

To top


Beams

The underground has to be clean, dry, solid, smooth and able to take a weight. Cut beams with a fine saw. Apply DECOSA® universal glue on beam-backside. Set position, press beam firmly against wall/ceiling and support for 24 - 48 hours. Remove excess glue rests with a wet sponge immediately. Finally apply corbels. Joints can be covered with fittings, spackle and stain.

To top